| 1 |
Redution of Oxides Using CaO Electrolysis in Molten Calcium Chloride |
R. O. Suzuki |
[Molten Salts, Vol. 53, No. 1(2010), pp. 1-8] |
| 2 |
Influence of Zincate Pretreatment on Adhesion Strength of a Copper Electroplating Layer on AZ91 D Magnesium Alloy |
K. Azumi |
[Surface & Coatings Technology 205(2011), 3050-3057] |
| 3 |
Optimization of Pulsed Electrodeposition of Aluminum from AlCl3-1-ethyl-3-methylimidazolium Chloride Ionic Liquid |
K. Azumi |
[Electrochimica Acta 56(2011), 1130-1137] |
| 4 |
Formation of Porous Anodic Titanium Oxide Films in Hot Phosphate/Glycerol Electrolyte |
H. Habazaki |
[Electrochimica Acta, Vol. 16(2010), pp. 3939-3943] |
| 5 |
Two-step Plasma Electrolytic Oxidation of Ti-15V-3Al-3Cr-3Sn for Wear-resistant and Adhesive Coating |
H. Habazaki |
[Surface & Coatings Technology 205(2011)4732-4740] |
| 6 |
Low Temperature Synthesis of MgTiO3 by Application of Magnesium Corrosion in an Organic Solvent |
O. Seri |
[J. Japan Inst. Metals, Vol. 74, No. 8(2010), pp. 527-532] |
| 7 |
Effects of Lamellar Thickness on Misfit Dislocation introduction and Mechanical Properties of γ/α2 Nano-lamellar TiAl Alloys |
K. Maruyama |
[J.Physics, Conference Series, Vol. 240(2010), 012101 1~4] |
| 8 |
Calcium Phosphate Coating on Titanium Using Dry Process |
T. Narushima |
[Materials Science Forum Vols. 654-656 (2010) , pp. 2162-2167 ] |
| 9 |
Effect of Flexural Rigidity of Tool on Machining Accuracy during Microgrooving by Ultrasonic Vibration Cutting Method |
T. Furusawa |
[Japanese Journal of Applied Physics, 49(2010)126701] |
| 10 |
Behavior of Hydrogen in Aluminum Exposed in Different Atmospheres |
G. Itoh |
[The Journal of Japan Institute of Light Metals, Vol. 60, No. 9(2010), pp. 433-437] |
| 11 |
Thermal Desorption Spectroscopy Study on the Hydrogen Trapping States in a Pure Aluminum |
G. Itoh |
[Materials Transactions, Vol. 52, No. 2(2011), pp. 130-134] |
| 12 |
Development of Prediction of Surface Accuracy in Hemmed Parts by Springback Simulation |
S. Takahashi |
[Journal of the JSTP, Vol. 51, No. 597(2010), pp. 963-968] |
| 13 |
Mechanical Properties and Microstructures of Severely Plastic Deformed Pure Titanium by Mechanical Milling and Spark Plasma Sintering |
M. Kubota |
[Materials Science Forum Vols. 667-669(2011), pp. 559-564] |
| 14 |
Deep Drawing of 5052 Aluminum Alloy Sheets Using Diamond Tools without Lubricant |
N. Koga |
[Journal of Japan Institute of Light Metals, Vol. 61, No. 3(2011), pp. 107-111] |
| 15 |
Thermoelectric Properties of Icosahedral Al-Pd-(Mn or Re) Quasicrystals: Improvement of the ZT Value by Ga Substitution for Al Atoms |
K. Kiumura |
[Journal of Electronic Materials, Vol. 39(2010), pp. 1885-1889] |
| 16 |
Thermoelectric Properties of Binary Semiconducting Intermetallic Compounds Al2Ru and Ga2Ru Synthesized by Spark Plasma Sintering Process |
K. Kiumura |
[Materials Transactions, Vol. 51(2010), pp. 988-993] |
| 17 |
Effect of High-frequency Switching Electrolysis on Film Thickness Uniformity of Anodic Oxide Film Formed on AC8A Aluminum Alloy |
S. Ono |
[J. Jpn. Inst. Light Metals, Vol. 60, No. 11(2010), pp. 602-607] |
| 18 |
Anodizing under Sparking of AZ31B Magnesium Alloy in Na3PO4 Electrolyte |
S. Ono |
[J. Jpn. Inst. Light Metals, Vol. 60, No. 11(2010), pp. 608-614] |
| 19 |
Comparison of Cutting Forces and Cut Surfaces between New Shearing Method with Horizontal Tool Movement and Conventional Shearing |
M. Murata |
[Journal of Japan Institute of Light Metals, Vol. 61, No. 3-6(2011), pp. 100-106] |
| 20 |
Grain Refinement by Combined ECAE/Extrusion and Dieless Drawing Processes for AZ31 Magnesium Alloy Tubes |
K. Manabe |
[Materials Science Forum, Vols. 654-656(2010), pp. 735-738] |
| 21 |
Nanoimprinting Process Using Highly Ordered Anodic Porous Alumina |
H. Masuda |
[ECS Transaction, Vol. 33 No. 16(2011), pp. 67] |
| 22 |
Formation of Internal Crack in High Speed Twin-Roll Cast 6022 Aluminum Alloy Strip |
S. Kumai |
[Materials Transactions, Vol. 51, No. 10(2010), pp. 1854-1860] |
| 23 |
High-Speed Twin-Roll Casting of Al-Si Based Alloys |
S. Kumai |
[Proceedings of the 12th International Conference on Aluminium Alloys, September 5-9, (2010), pp. 693-697] |
| 24 |
Effect of Secondary-Phase Particle Morphology on Tear Toughness of Al-Mg-Si-Mn Aluminum Alloy Castings |
S. Kumai |
[Proceedings of the 12th International Conference on Aluminium Alloys, September 5-9, 2010, Yokohama, Japan, ©2010 The Japan Institute of Light Metals, pp. 1314-1318] |
| 25 |
New Creep Region in Pure Face-centered Cubic Metals at Low Temperatures |
E. Sato |
[Scripta Materialia, 63(2010), 516-519] |
| 26 |
Plating Out Oil Film Thickness on Roll and Workpiece During Cold Rolling with O/W Emulsion |
A. Azushima |
[Tribology Transactions, 54(2011), pp. 275-281] |
| 27 |
A Review of the Mechanics of Metal Spinning |
K. Kawai |
[The Journal of Materials Processing Technology, Vol. 210(2010), pp. 3-23] |
| 28 |
{001} Texture Map of AA5182 Aluminum Alloy for High Temperature Uniaxial Compression |
H. Fukutomi |
[Mater. Trans. Vol. 51, No. 12(2010), 2162-2167] |
| 29 |
Statistical Assessment of Fatigue Crack Initiation from Sub-surface Hydrogen Micropores in High-quality Die-cast Aluminum |
H. Toda |
[Acta Materialia, Vol. 59, No. 12(2011), pp. 4990-4998] |
| 30 |
In-situ Observation of Ductile Fracture Using X-ray Tomography Technique |
H. Toda |
[Acta Materialia, Vol. 59, No. 5(2011), pp. 1995-2008] |
| 31 |
Application of Dual-energy K-edge Subtraction Imaging to Assessment of Heat Treatments in Al-Cu Alloys |
H. Toda |
[Materials Transactions, Vol. 51, No. 11(2010), pp. 2045-2048] |
| 32 |
Four-dimensional Annihilation Behaviors of Micro Pores during Surface Cold Working |
H. Toda |
[Materials Transactions, Vol. 51, No. 7(2010), pp. 1288-1295] |
| 33 |
Effect of Rotation Number on Microstructure of AZ61 Magnesium Alloy Produced by Compressive Torsion Processing |
N. Kanetake |
[Journal of Japan Society for Technology of Plasticity, Vol. 51, No. 588(2010), pp. 38-42] |
| 34 |
Flexible Photonic Crystal via Alumina Ball Inserted Teflon Tube |
Y. Watanabe |
[Applied Physics A, 100, No. 4, 981-985(2010)] |
| 35 |
Wear of Al/Al3Zr Functionally Graded Materials Fabricated by Centrifugal Solid-Particle Method |
Y. Watanabe |
[J. Mater. Proc. Tech., 210, No. 15, 2245-2251(2010)] |
| 36 |
Cold Model for Process of a Ni-aluminides/ Steel Clad Pipe by a Reactive Centrifugal Casting Method |
Y. Watanabe |
[Mater. Letter, 65, No. 3, 467-470(2011)] |
| 37 |
Fabrication of Al/Al3Ti Functionally Graded Materials by Reaction Centrifugal Mixed-Powder Method |
Y. Watanabe |
[Jpn. J. Appl. Phys., 50, No. 1, 01AJ02-1-01AJ02-7(2011)] |
| 38 |
Microstructural Characterization and Tribocorrosion Behaviour of Al/Al3Ti and Al/Al3Zr FGMs |
Y. Watanabe |
[Wear, 270, Nos. 11-12, 806-814(2011)] |
| 39 |
Corrosion Behaviour of Al/Al3Ti and Al/Al3Zr Functionally Graded Materials Produced by Centrifugal Solid-particle Method: Influence of the Intermetallics Volume Fraction |
Y. Watanabe |
[Corrosion Science, 53, No. 6, 2058-2065(2011)] |
| 40 |
Investigation of Novel Centrifugal Casting Method Using Machining Chips by Al System |
Y. Watanabe |
[J. Japan Inst. Materials, Vol. 75, No. 5, 320-326(2011)] |
| 41 |
Crystal-Plasticity Finite-Element Analysis of Inelastic Behavior during Unloading in a Magnesium Alloy Sheet |
H. Takuda |
[International Journal of Plasticity, 27(2011), pp. 1072-1092] |
| 42 |
Influence of Zn Concentration on Stretch Formability at Room Temperature of Mg-Zn-Ce Alloy |
M. Mabuchi |
[Materials Science and Engineering A, Vol. 528., Vol. 2(2010), pp. 566-572] |
| 43 |
Microstructure, Texture and Mechanical Properties of Mg-Zn-Ce Alloy Extruded at Different Temperatures |
M. Mabuchi |
[Materials Transactions, Vol. 52, No. 6(2011), pp. 1104-1107] |
| 44 |
Fabrication of Lotus-type Porous Aluminum by Continuous Casting Technique |
H. Nakajima |
[Proceedings of the 12th International Conference on Aluminum Alloys, September 5-9, 2010, Yokohama, Japan, The Japan Institute of Light Metals, pp. 1639-1644] |
| 45 |
Deformation Behavior of Al Wire during Ultrasonic Bonding |
Y. Takahashi |
[Proceeding of MATE 2011, Japan Welding Soc., Vol 17, (2011), pp. 225-230] |
| 46 |
Nanoindentation Measurement of Interfacial Reaction Layers in 6000 Series Aluminum Alloys and Steel Dissimilar Metal Joints with Alloying Elements |
A. Hirose |
[Materials Transactions, Vol. 52(2011), pp. 979-984] |
| 47 |
Formation of New Bone with Preferentially Oriented Biological Apatite Crystals Using a Novel Cylindrical Implant Containing Anisotropic Open Pores Fabricated by the Electron Beam Melting (EBM) Method |
T. Nakano |
[ISIJ International, Vol. 51, No. 2(2011), pp. 262-268] |
| 48 |
Phase Constitution and Heat Treatment Behavior of Ti-7mass% Mn-Al Alloys |
M. Ikeda |
[Materials Science Forum Vols. 654-656(2010), pp. 855-858] |
| 49 |
First-principles calculation of Grain Boundary Energy and Grain Boundary Excess Free Volume in Aluminum: Role of Grain Boundary Elastic Energy |
K. Higashi |
[Journal of Materials Science, Vol. 46, No. 12(2011), pp. 4199-4205] |
| 50 |
Preparation of Sintered Alloys in the System Mg-Ge and Anodic Properties in Lithium Secondary Batteries |
T. Esaka |
[Electrochemistry, Vol. 78, No. 8(2010), pp. 666-670] |
| 51 |
High Strain-Rate Compressive Response of Friction Stir Welded AA6061-T6 Joints: Effect of Welding Parameter |
T. Yokoyama |
[Journal of the Japanese Society for Experimental Mechanics, 10, Special Issue, (2010), pp. 168-173] |
| 52 |
Fatigue Strength of Al-evaporated Al-Zn Alloys with High Zn Concentration |
T. Kanadani |
[Proceedings of the 12th International Conference on Aluminium Alloys (ICAA 12), September 5-9, 2010, Yokohama, Japan, The Japan Institute of Light Metals, pp. 2357-2362] |
| 53 |
Precipitation of β' Phase in a Low Cost Beta Titanium Alloy |
K. Nakai |
[Materials Science Forum, Vols. 638-642(2010), pp. 461-464] |
| 54 |
Relationship between Vickers Micro Hardness and Proof Stress in Age Hardening Aluminum Alloys |
M. Furukawa |
[Journal of the Japan Society of Technology Education in Kyushu Branch, Vol. 18(2010), pp. 27-33] |
| 55 |
Deformation of Semi-Solid Al-SiC Alloy Compressed in the Drop-Forge Viscometer |
Y. Fukui |
[Trans. JSME, Vol. 76, No. 772A(2010), pp. 1735-1740] |
| 56 |
Quantification of Creep Rate Change and Life Prediction by Means of Strain-Acceleration-Parameter |
H. Sato |
[KEIKINZOKU, Vol. 60, No. 7(2010), pp. 353-357] |
| 57 |
Effects of Sand Compaction and Reduced Pressure on Dimensional Change of Aluminum Alloy Casting in Expendable Pattern Casting Process |
S. Koroyasu |
[The Forth International Congress on Expendable Pattern Casting Technology in China, (2010), pp. 94-101] |
| 58 |
ELID Grinding Characteristics of Ti Alloy Using Electro-conductive Porous Rubber Bonded Wheel |
N. Itoh |
[Japan Society for Abrasive Technology (2010), Vol. 54, No. 2, pp. 101-104] |
| 59 |
Mechanisms of Ultrafine Grain Formation in Severe Plastic Deformation |
H. Miura |
[Materials Science Forum, Vols. 638-642(2010), pp. 98-103 ] |
| 60 |
Microstructure and Mechanical Properties of AZ61 Mg Alloy Prepared by Multi Directional Forging |
H. Miura |
[Transactions of Nonferrous Metals Society of China, Vol. 20(2010), pp. 1294-1298] |
| 61 |
Mechanical Properties of Titanium Particles Dispersed Magnesium Matrix Composite Produced through Accumulative Diffusion Bonding Process |
K. Kitazono |
[Mater. Trans., Vol. 52, No. 2(2011), pp. 155-158] |
| 62 |
The Compositions of Metastable Phase Precipitates Observed at Peak Hardness Condition in an Al-Mg-Si Alloy |
M. Takeda |
[Journal of Alloys and Compounds, Vol. 509(2011), pp. 241-245] |
| 63 |
Experimental and Computational Studies of Competitive Precipitation Behavior Observed in an Al-Mg-Si Alloy with High Dislocation Density and Ultrafine-grained Microstructures |
S. Hirosawa |
[Journal of Japan Institute of Metals, Vol. 75, No. 5(2011), pp. 283-290] |
| 64 |
Relationship between the Generation of Deformation band and the Preceding Inhomogeneous Deformation in Tensile Deformed 5083-O Aluminum Alloy Sheet |
Y. Nakayama |
[J. Jpn. Inst. Light Met., Vol. 61, No. 6(2011), pp. 240-245] |
| 65 |
Low-cycle Fatigue Behavior of an Al-Mg-Si Alloy with and without a Small Addition of Sc |
C. Watanabe |
[Material Science Forum, Vols. 654-656(2010), pp. 938-941] |
| 66 |
Thermoelectric Properties of Si2Ti-Type Al-Mn-Si Alloys |
T. Takeuchi |
[Materials Transactions Vol. 51, No. 6(2010), pp. 1127 to 1135] |
| 67 |
Testing Techniques to Eliminate Frictional Effect and to Achieve Constant Strain-Rate in Split Hopkinson Pressure Bar Impact Compression System |
M. Yamashita |
[Materials Science Forum, Vol. 673(2011), pp. 77-82] |
| 68 |
Fatigue Behaviour of Cast Aluminum Alloy Surface-modified by Friction Stir Surface Processing |
Y. Uematsu |
[Steel Research International, Vol. 81, Issue 9(2010), pp. 1084-1087] |
| 69 |
Effect of Titanium-Fine-Particle Bombarding Treatment on Corrosion Resistance of Aluminum Alloy and Carbon Steel |
T. Morita |
[Published in Transactions of the Japan Society of Mechanical Engineers (Series A), Vol. 77(2011), No. 781, pp. 1500-1508] |
| 70 |
Hydrogen Evolution during Fatigue Deformation in 6061 and 7075 Aluminum Alloys |
K. Horikawa |
[Proceedings of the 12th International Conference on Aluminum Alloys, (2010), pp. 371-376] |
| 71 |
Change in Crystal Orientations of a {100}<001>Pure Aluminum Single Crystal during Accumulative Roll Bonding |
K. Kashihara |
[Materials Transactions, Vol. 52, No. 5(2011), pp. 825-829] |
| 72 |
Cold Joining of Aluminum Sheets by Shot Peening |
Y. Harada |
[ICAA12(The 12th International Conference on Aluminium Alloys), (2010), pp. 1786-1790] |
