|
|
| Fabrication of Micro-Circuit Board by Aluminum Anodizing and Laser Irradiation - Effect of Laser Irradiation Condition on Micro-Pattern Formation - |
|
|
[J. Surf. Finish. Soc. Jpn., 56(2005)528-534]
|
|
|
| Influence of Acetic Acid on Corrosion Behavior of 1100 Pure Aluminum |
|
|
[J. Light Japan Inst. Metals, vol. 55, No. 4, (2005), pp. 175-180]
|
|
|
| Phase Stability and Interdiffusivity of the L10-based Ordered Phases in Al-rich Portion of the Ti-Al Binary System |
|
|
[Intermetallics, vol. 13(2005). pp. 784-791]
|
|
|
| Alloying Effect on the Hydrogen Sensing Property of Melt-Spun Mg90Pd10 Amorphous Alloy |
|
|
[Materials Transactions, Vol. 46, No. 3(2005), pp. 738-741]
|
|
|
Effect of  2 Spacing on Creep Deformation Characteristics of Hard Oriented PST Crystals of TiAl Alloy |
|
|
[Intermetallics, Vol. 13, No. 10(2005), pp. 1116-1121]
|
|
|
| Effect of Ta Content on Mechanical Properties of Ti-30Nb-XTa-5Zr |
|
|
[Materials Science and Engineering C, Vol. 25(2005), pp. 370-376]
|
|
|
| Dental Precision Casting of Ti-29Nb-13Ta-4.6Zr Using Calcia Mold |
|
|
[Materials Science Forum, Vols. 475-479(2005), pp. 2303-2308]
|
|
|
Fatigue Characteristics of Low Cost  Titanium Alloys for Medical and Healthcare Applications |
|
|
[Materials Transactions, Vol. 46, No. 7(2005), pp. 1570-1577]
|
|
|
| Improvement in Fatigue Characteristics of Newly Developed Beta Type Titanium Alloy for Biomedical Applications by Thermo-mechanical Treatments |
|
|
[Mater. Sci. Eng. C, Vol. 25, No. 6(2005), pp. 248-254]
|
|
|
| Mechanical Properties of Biocompatible Beta-type Titanium Alloy Coated with Calcium Phosphate Invert Glass-Ceramic Layer |
|
|
[Mater. Trans., JIM, Vol. 46, No. 7(2005), pp. 1564-1569]
|
|
|
| Mechanical Properties and Deformation Behavior of -type Titanium Alloy(TNTZ) Drawn Wires |
|
|
[Japan Inst. Metals, Vol. 69, No. 7(2005), pp. 530-537]
|
|
|
| Achieving High Strain rate Superplasticity in an Al-Li-Mg Alloy through Equal Channel Angular Extrusion |
|
|
[Materials Science and Technology, Vol. 21, No. 4(2005), pp. 408-418]
|
|
|
| Continuous Dynamic Recrystallization in an Al-Li-Mg-Sc Alloy during Equal-Channel Angular Extrusion |
|
|
[Materials Science and Engineering, Vol. A396(2005), pp. 341-351]
|
|
|
| The Improvement of Tribological and Fatigue Properties of Aluminum Alloy Coated DLC Hybrid Surface Modificationn |
|
|
[Transactions of the Japan Society of Mechanical Engineering, Series A, Vol. 72, No. 718(2006), pp. 907-913]
|
|
|
| Microstructural Modification in a Beta Titanium Alloy for Implant Applications |
|
|
[Materials Transactions, Vol. 47, No. 1(2006), pp. 90-95]
|
|
|
| Effect of Heat Treatment Condition on the Hydrogen Content in Al-4%Mg Alloys |
|
|
[The Journal of Japan Institute of Light Metals, Vol. 56, No. 4(2006), pp. 203-209]
|
|
|
| Microstructures and Mechanical Properties of AZ91 Magnesium Alloy Castings by Friction Stir Welding |
|
|
[Journal of Japan Institute of Light Metals, Vol. 55, No. 6(2005), pp. 259-264]
|
|
|
| Friction Welding of Aluminum to Copper |
|
|
[Journal of Light Metal Welding & Construction, Vol. 43, No. 8(2005), pp. 392-400]
|
|
|
| Structure and Properties of Rapidly Solidified Mg-5Ca-Al-Zn Alloys |
|
|
[Journal of Japan Institute of Light Metals, Vol. 55, No. 3(2005), pp. 137-141]
|
|
|
| Air Bending of AZ31 Magnesium Alloy Sheets |
|
|
[Journals of Japan Institute of Light Metals, Vol. 55, No. 4(2005), pp. 181-185]
|
|
|
|
| A Compton Scattering Study on the Hume-Rotherymechanism of AlCu-TM(TM: Transition Metal) Quasicrystals |
|
|
[Journal of Physics: Condensed Master, 18(2006), 7203-7208]
|
|
|
| Experimental and Computational Investigation of Formation of Precipitate Free Zones in an Al-Cu Alloy |
|
|
[Materials Transactions, Vol. 46, No. 6(2005), pp. 1230-1234]
|
|
|
| Structure and Dielectric Property of Anodic Barrier Films Formed on Aluminum in Low Voltage Range |
|
|
[Electrochimica Acta, Vol. 50(2005), pp. 5103-5110]
|
|
|
| Design of Two-Dimensional/three-Dimensional Composite Porous Alumina by Colloidal Crystal Templating and Subsequent Anodization |
|
|
[Appl. Phys. Lett., Vol. 87, No. 10(2005), pp. 103102-1—103102-3]
|
|
|
| Natural Lighography of Si Surfaces Using Localized Anodization and Subsequent Chemical Etching |
|
|
[Electrochemical and Solid-State Letters, Vol. 8, No. 7(2005), pp. G172-G175]
|
|
|
| Isochronal Annealing Behaviors of Magnesium Alloy AZ31 after Hot Deformation |
|
|
[Materials Transactions, Vol. 46(2005), pp. 2981-2987]
|
|
|
| High Angle Boundary Formation in Dynamically Recovered Materials during Severe Hot Forging |
|
|
[Ultrafine Grained Materials IV. Edited by Y. T. Shu, T. G. Langdon, Z. Horita, M. J. Zehetbaouer, S. L. Semiatin and T. C. Lowe. TMS(The Minerals, Metals & Materials Society), 2006, pp. 73-80]
|
|
|
| Compression Spinning of Circular Magnesium Tube Using Heated Roller Tool |
|
|
[J. of Materials Processing Technology, 163-164(2005), 540-545]
|
|
|
| An Experimental Study on Spinning of Taper Shape on Tube End |
|
|
[Journal of Materials Processing Technology, 166(2005), 405-410]
|
|
|
| Influence of Strip Materials on Behavior of Incremental In-plane Bending |
|
|
[Journal Materials Processing Technology, 162-163C(2005), pp. 190-195]
|
|
|
| Deformation Analysis for the Shear Bending Process of Circular Tubes |
|
|
[The Journal of Materials Processing Technology, Vol. 162-163(2005), pp. 492-497]
|
|
|
| Finite Element Analysis of Magnesium AZ31 Alloy Sheet in Warm Deep-Drawing Process Considering Heat Transfer Effect |
|
|
[Materials Letters, Vol. 60, Issue 15(2006), pp. 1866-1870]
|
|
|
| Highly Ordered Anodic Porous Alumina by Imprinting Using Ni Molds Prepared from Ordered Array of Polystyrene Particles |
|
|
[Japanese Journal of Applied Physics Part 1, Vol. 44, No. 10(2005), pp. 7726-7728]
|
|
|
| Direct Observation of Asperity Deformation of Specimens with Random Rough Surfaces in Upsetting and Indentation Processes |
|
|
[Wear, 260(2006), 258-264]
|
|
|
| Production of Ti-43mol%Al with Oriented Lamellar Microstructure and Its Creep Characteristics |
|
|
[J. JILM, Vol. 55, No. 8(2005), pp. 343-349]
|
|
|
| Magnesium Foam Produced from Bulk AZ31 Magnesium Alloy Sheets |
|
|
[Materials Science Forum, 475-479(2005), 501-504]
|
|
|
| Improvement in Surface Properties of Mg-Al-Zn Based Alloy Cutting Chip Extrusions |
|
|
[Journal of Japan Institute of Light Metals, Vol. 55, No. 9(2005), pp. 400-404]
|
|
|
| Effect of Extrusion Speed on Extrudate Properties of AZ31B Magnesium Alloy Machined Chip |
|
|
[Journal of Japan Institute of Light Metals, Vol. 56, No. 3(2006), pp. 166-171]
|
|
|
| Improving the Superplastic Properties of a Two-phase Mg-8%Li Alloy through Processing by ECAP |
|
|
[Materials Science and Engineering A, Vol. 410-411(2005), pp. 439-442]
|
|
|
| Comparison of Precipitates between Excess-Si Type and Balanced Type Al-Mg-Si Alloys during Continuous Heating |
|
|
[The Metallurgical and Materials Transactions A, Vol. 36A, pp. 2007-2012, 2005]
|
|
|
|
| Superconductivity and Thermal Property of MgB2/Al Composite Materials |
|
|
[The Journal of Japan Institute of Metals, Vol. 69, pp. 977-982, 2005]
|
|
|
| Liquid Adhesion Phenomenon to Ultrasonically Vibrating Horn End and Its Application of Casting Process |
|
|
[J. JFS, Vol. 77, No. 11, pp. 752-758(2005)]
|
|
|
| Improvement of the Drawability of 6061 Aluminum Alloy Sheets by the Local Solution Treatment |
|
|
[Journal of Japan Institute of Light Metals, Vol. 55, No. 1(2005), pp. 33-36]
|
|
|
| Influence of Punch Shape on Drawability of Locally Solution Treated 6061 Aluminum Alloy Sheets |
|
|
[Journal of Japan Institute of Light Metals, Vol. 55, No. 7(2005), pp. 306-309]
|
|
|
| In-Situ Scanning Electron Microscopy Observation of the Pattern Formation on the Surface of Al/Ge Bilayer Films |
|
|
[Materials Science Forum, Vol. 539-543(2007), pp. 3568-3573]
|
|
|
| Effect of Texture Evolution on Tensile Properties of Al-Ni Eutectic Alloy |
|
|
[Materials Science and Technology, 21, 708-714(2005)]
|
|
|
| Backward Extrusion of Al-Al3Ti Functionally Graded Material: Volume Fraction Gradient and Anisotropic Orientation of Al3Ti Particles |
|
|
[Scripta Mater., 53, 687-692(2005)]
|
|
|
| Microscopic Study of Al-base Intermetallic Compound-dispersed Functionally Graded Materials Fabricated by a Centrifugal Method |
|
|
[FORMATEX Microscopy Book Series(No.2), Current Issues on Multidisciplinary Microscopy Research and Education, 189-198(2005)]
|
|
|
| Microstructures of Functionally Graded Materials Fabricated by Centrifugal Solid-Particle and in-situ Method |
|
|
[Metals and Materials International, 11, 391-399(2005)]
|
|
|
| Grain Refining Performance for Al and Al-Si Alloy |
|
|
[Mater. Sci. Eng. A, A425, 55-63(2006)]
|
|
|
| Influence of Microstructure on Electrochemical Properties of Severely Deformed Al-5 wt% Cu Alloy by ECAP |
|
|
[Materials Science Forum, 519-521, 705-710(2006)]
|
|
|
| Grain Refinement Performance of Aluminum Cast-Alloy by Deformed Al-Al3Ti Alloy Refiner |
|
|
[Materials Science Forum, 519-521, 1859-1864(2006)]
|
|
|
| Effect of Zr Addition on Microstructure of Hot Extruded P/M Al-Zn-Mg-Cu Alloys |
|
|
[Journal of Japan Institute of Light Metals, Vol. 5, No. 4(2005), 164-168]
|
|
|
| Fracture and Debonding Behavior of Coated Brittle Alumina Layer on Ductile Aluminum Substrate Wire |
|
|
[Composite Interfaces, Vol. 12, No. 3/4(2005), pp. 311-324]
|
|
|
| Finite Element Simulation of Warm Deep Drawing of AZ31 Magnesium Alloy Sheet |
|
|
[The Japan Society for Technology of Plasticity, Vol. 47, No. 541(2006), pp. 129-133]
|
|
|
| A New Cross Rolling for Spreading of Thin Strips and Its Application for Texture Control of Aluminium |
|
|
[Advanced Technology of Plasticity(2005), Proceeding of the 8th ICTP, held in Oct. 9-13, 2005 in Verone, Italy ]
|
|
|
| Effect of Tool Shape on Mechanical Properties and Microstructure of Friction Stir Welded Aluminum Alloys |
|
|
[Materials Science and Technology A419(2006)25-31]
|
|
|
| Application of Nd: YAG Laser to Aluminum Alloy Sorting |
|
|
[Mater. Trans., Vol. 46, No. 12(2005), pp. 2641-2646]
|
|
|
| Vibration-damping Capacity of Lotus-type Porous Magnesium |
|
|
[Materials Science and Engineering A 417(2006), 129-133]
|
|
|
| Evolution of Antiphase Domain (APD)/ Nanolamellar Complex Structure in Ti-Al Single Crystals |
|
|
[Material Science & Technology 1(2005), pp. 39-46]
|
|
|
|
| The Influence of Cr Content on Phase Constitution, Electrical Resistivity and Vickers Hardness in Ti-Cr Binary Alloys Quenched from a Temperature within Beta Phase Region |
|
|
[Journal of Light Metals, Vol. 55, No. 11(2005), pp. 582-586]
|
|
|
| Silicon Carbide Nanofibers Synthesized Using Simple Chemical Vapor Reaction |
|
|
[Proceedings of the 5th International Conference on High Temperature Ceramic Matrix Composites (HTCMC 5), The American Ceramic Society, 2005, pp. 11-16]
|
|
|
| Low-Temperature and High-Temperature Environmental Embrittlement of TiAl-Based Intermetallic Alloys |
|
|
[J. of Japan Institute of Light Metals, Vol. 55, No. 9(2005), pp. 405-411]
|
|
|
| Elastic Constants of AlLi from First Principles |
|
|
[Materials Transactions, Vol. 46(2005), pp. 1117-1121]
|
|
|
| Experimental Investigation of Cavitation Behavior in AZ61 Magnesium Alloy |
|
|
[Materials Transactions, Vol. 46(2005), pp. 626-630]
|
|
|
| Determination of Impact Tensile Properties of Structural Epoxy Adhesive Butt Joints Using a Hat-shaped Specimen |
|
|
[Journal de Physique, IV 134(2006), pp. 789-795]
|
|
|
| Study of Dynamical Behavior of Helium Bubbles by in-situ TEM Observation |
|
|
[Materia Japan, Vol. 45(2006), 106-113]
|
|
|
| Study on Coanda Effect of the Supersonic Jet with Shock Waves |
|
|
[Journal of the Visualization Society of Japan, Vol. 25, Suppl. No. 2(2005), 51-54]
|
|
|
| Boron Effects on AE Event Rate Peaks during Tensile Deformation of Ni3Al Intermetallic Compound |
|
|
[Journal of Acoustic Emission, Vol. 23(2005), pp. 189-195]
|
|
|
| Achieving High Strength and High Ductility in Precipitation-Hardened Alloys |
|
|
[Advanced Materials, 17(2005), pp. 1599-1602]
|
|
|
| Developing High-Pressure Torsion for Use with Bulk Samples |
|
|
[Materials Science and Engineering, A 406(2005), pp. 268-273]
|
|
|
| Grain Refinement and Superplastic Flow in an Aluminum Alloy Processed by High-Pressure Torsion |
|
|
[Materials Science and Engineering, A408, (2005), pp. 141-146]
|
|
|
| Grain Refinement and Superplasticity in a Magnesium Alloy Processed by Equal-Channel Angular Pressing |
|
|
[Metallurgical and Materials Transaction, 36A, (2005), pp. 1705-1711]
|
|
|
| Exceptional Superplasticity in an AZ61 Magnesium Alloy Processed by Extrusion and ECAP |
|
|
[Materials Science and Engineering, A420, (2006), pp. 240-244]
|
|
|
| Preparation of Samples Using a Chemical Etching for SEM/EBSP Method in a Pure Magnesium Polycrystal and Analysis of Its Twin Boundaries |
|
|
[Journal of Japan Institute of Light Metals, Vol. 55, No. 3, (2005), pp. 131-136]
|
|
|
| Energy and Structure of [1100] Symmetric Tilt Grain Boundaries in Magnesium |
|
|
[Journal of the Japan Institute of Metals, Vol. 69, No. 3, (2005), pp. 303-307]
|
|
|
| An Investigation of the Deformation Process during Equal-Cannel Angular Pressing of an Aluminum Single Crystal |
|
|
[Materials Science & Engineering A, 410-411, (2005), pp. 194-200]
|
|
|
| An Investigation of Deformation in Copper Single Crystals Using Equal-Channel Angular Pressing |
|
|
[Material Science Forum, 503-504, (2006), pp. 113-118]
|
|
|
| A Quantitative Study of Cavity Development in the Tensile Testing of an Aluminum Metal Matrix Composite Processed by Equal-Channel Angular Pressing |
|
|
[Materials Science & Engineering A, 410-411, (2005), pp. 402-407]
|
|
|
| Influence of Crystal Orientation on ECAP of Aluminum Single Crystals |
|
|
[Material Science & Engineering A, 420, (2006), pp. 79-86]
|
|
|
|
| Characteristics of a Near-Net-Shape Formed Al-Al3Fe Eco-Functionally Graded Material Produced over Its Eutectic Melting Temperature |
|
|
[Materials Science and Engineering A, Vol. 416, No. 1(2006), pp. 80-91]
|
|
|
| Superplasticity and Crystallographic Orientation Distribution in Friction Stir Processed Sheet of an Al-Mg-Mn Alloy |
|
|
[Materials Science Forum, 475-479, (2005), pp. 3029-3032]
|
|
|
| Microstructural Control in Surface Layers of a Commercial Purity Titanium Sheet Using Continuous Cyclic Bending and Its Bendability |
|
|
[Journal of Japan Institute of Light Metals, 55(2005), pp. 587-591]
|
|
|
| Restraint of the Burr When Cutting of Austenite Stainless Steel by the Application of Magnetic Field Assisted Method |
|
|
[Proc. of the Inter. Conf. on Leading Edge Manufacturing in 21st Century, JSME, (2005), pp. 1149-1154]
|
|
|
| Categorization of Ambient-Temperature Creep Behavior of Metals and Alloys on Their Crystallographic Structures |
|
|
[Journal of Japan Institute of Light Metals, Vol. 55, No. 11(2005), 604-609]
|
|
|
| Serration, Deformation band Propagation and Strain Marking in a 5083 Aluminum Alloy at Low Temperature |
|
|
[J. Japan Institute of Light Metals, Vol. 56, No. 1(2006), pp. 39-44]
|
|
|
| Laser Cladding of Fe-Cr-C Alloys on A5052 Aluminum Alloy Using Diode Laser |
|
|
[Materials Transactions, Vol. 46, No. 6(2005), pp. 1341-1347]
|
|
|
| Experimental Investigation on Roughening of the Matt Surface in Pack Rolling |
|
|
[Journal of Materials Processing Technology, Vol. 177(2006), pp. 501-504]
|
|
|
| Visualization of Hydrides in Titanium by Means of Diffraction-enhanced X-ray Imaging |
|
|
[Journal of Alloys and Compounds, Vol. 402, No. 9(2005), pp. 109-114]
|
|
|
| Visualization of Hydride in Titanium and Titanium Alloy by Refraction-enhanced X-ray Imaging Technique |
|
|
[Materials Transaction, Vol. 47, No. 5(2006), pp. 1299-1302]
|
|
|
| Effect of Ultrasonic Vibration on Infiltration of Nickel Porous Preform with Molten Aluminum Alloys |
|
|
[Mat. Trans., 46, 10(2005), pp. 2156-2158]
|
|
|
| Deformation and Recrystallization of Aluminum Bicrystals Having Asymmetric Tilt Grain Boundary |
|
|
[Materials Transactions, Vol. 47, No. 3(2006), pp. 838 - 844]
|
|
|
| Orientation Dependence of Ductility of Mg Single Crystals at Elevated Temperature |
|
|
[Materials Science Forum Vols. 488-489(2005), pp. 193-196]
|
|
|
| High Temperature Deformation and Extended Plasticity in Mg Single Crystals |
|
|
[Phil. Mag., Vol. 85, pp. 3533-3565(2005)]
|
|
|
| Grain-Size Dependence of Microstructural Evolution and Mechanical Behavior during High-Temperature Deformation of Mg and Mg Alloy |
|
|
[Proceedings of 1st Asian Symposium on Magnesium Alloys, Jeju, Korea, 2005, pp. 77-80(Invited)]
|
|
