INDEX
| No | Title | Author |
|---|---|---|
| 1 | Effect of Relatively Insoluble Compounds on β Phase Precipitation in 5083 Aluminum Alloy | T. Enjo |
| 2 | Study on the Structure and Mechanical Property of Unidirectionally Solidified Al-CuAl2 Eutectic Alloys | K. Hashiura |
| 3 | Study on the Spinnability of Aluminum and it’s Alloy | M. Hayama |
| 4 | Prolonged Aging of a Subperitectic Al-Zr Alloy | S. Hori |
| 5 | Effects of a Small Addition of Si on the Precipitation | S. Hori |
| 6 | Stress Induced Migration of 〈112〉 Symmetric Tilt Boundaries | R. Horiuchi |
| 7 | Apparent Viscosity and Structure in Partially Solidified Al-Cu Alloys | R. Ichikawa |
| 8 | The Correlation between Precipitates Formed by the Annealing of an Al-0.03Fe Alloy and its Recrystallization Textures | K. Ito |
| 9 | Resistivity Change of Age-Hardening Aluminum Alloys by Low Temperature Deformation | K. Kamei |
| 10 | Some Properties of Sintered Alloys | M. Kato |
| 11 | Experiment and Analysis of Plasto-Hydrodynamic Lubrication in Drawing of Aluminium and Copper Strips | H. Kudo |
| 12 | The Bauschinger Effect and Work-Hardening in Aluminium Single Crystals Dispersion-Hardened with Silicon Particles | K. Matsuura |
| 13 | Effect of Deformation Temperature on the Stage IV Deformation in 〈100〉 Oriented Aluminum Single Crystals | S. Miura |
| 14 | Plastic Deformation of Aluminum Bicrystals 〈100〉 Oriented | S. Miura |
| 15 | Plastic Deformation and Prominent Cross Slip of 〈100〉 oriented Aluminum Single Crystals | S. Miura |
| 16 | Plastic Deformation of Aluminum Bicrystals having Σ7 and Σ21 Coincidence Tilt Boundary | S. Miura |
| 17 | Plastic Deformation of 〈111〉 Oriented Aluminum Single Ctystals | S. Miura |
| 18 | Difference in Tensile Strength among Rayon-, PAN I- and PAN II- Type Graphite Fibres after Sodium- or Titanium- Boron Treatment in Aluminium Matrix Composites | S. Ochiai |
| 19 | ESCA Study of the Peeled Joint of Aluminum/Polyethylene/Aluminum Laminate | H. Endo |
| 20 | 180°-Peel Strength of Aluminum-Nylon 12 Laminate | M. Masuoka |
| 21 | Tensile Behavior of Aluminium Clad Supperplastic Alloy Sheet after Some Heat Treatments | H. Nishimura |
| 22 | Rolling Textures of Polycrystalline Aluminum Having Orientations Three-Dimensional Controlled —TEXTURES OF ROLLED SHEETS GROWTH TWINNED ALUMINUM (1ST REPORT)— |
S. Oya |
| 23 | Recrystallization Textures of Polycry-stalline Aluminum Having Orientations Three Dimensionally Controlled —TEXTURES OF ROLLED STEETS OF GROWTH TWINNED ALUMINUM (2ND REPORT)— |
S. Oya |
| 24 | Dependence of Press-Formability of Aluminum Sheets on Crystallographic Textures of Sheets and Cast Slabs | S. Oya |
| 25 | Growth of Growth Twin Crystals in Aluminum and Aluminum-Base Alloys | S. Oya |
| 26 | Thermal Behavior During Plastic Tension of Metals | K. Saito |
| 27 | Exoelectron Emission from a Mechanically Worked Aluminum Surface | T. Shibata |
| 28 | Experimental and Monte-Calro Studies of Multiple Scattering Correction in the Compton Profile of Aluminum | K. Suzuki |
| 29 | Distribution of Partial Drawing and Fracturing Loads in Cup Drawing along a Punch Periphery | Y. Tozawa |
| 30 | Elastic Stress and Strain Responses of the 〈110〉 Isoaxial and 〈001〉-〈111〉 Nonisoaxial Al Bicrystals | M. Ueda |
| 31 | Orientation Depence of Acoustic Emission During Plastic Deformation of an Aluminum Single Crystal | M. Ueda |
| 32 | Plastic Behaviors of the γ-phase in the Al-Mg System | K. Watanabe |
| 33 | Effects of a Small Amount of Ni on the Heat Resistance of Al-Zr Alloys | H. Yamada |
| 34 | Recrystallized Grain Size and Its Behavior of Al-Zr Alloys | H. Yamada |
| 35 | Strain Hardening and Recovery in High-Temperature Deformation by the Pure Metal Mode | H. Yoshinaga |
| 36 | Study of the Mechanism for Cutting Aluminium (XXVIII) CONSIDERATIONS ON THE BUILT-UP EDGE IN THE ORTHOGONAL CUTTING OF ALUMINIUM |
S. Zaima |
| 37 | Study on the Mechanism of Cutting Aluminium (XXIX) INFLUENCE OF CUTTING CONDITIONS ON THE RESIDUAL STRESS IN THE ORTHOGONAL CUT SURFACE OF ALUMINIUM |
S. Zaima |
| 38 | Study on the Machinability of the Aluminium Alloy (XXIII) ON THE REVERSING FINISH CUTTING ALUMINIUM |
S. Zaima |
| 39 | Study on the Mechanism of Cutting Aluminium (XXX) ON THE RELATIONS BETWEEN RESIDUAL STRESS AND MOIRE STRAIN IN THE ORTHOGONAL CUT SURFACE OF ALUMINIUM |
S. Zaima |
| 40 | Application of Tool Materials on the Cutting Aluminium-Silicon Cast Alloys (IV) ON THE WET CUTTING OF Al-Si CASTINGS AC3A |
S. Zaima |
| 41 | Application of Tool Materials on the Cutting Aluminium-Silicon Cast Alloy (V) TOOL WEAR IN WET CUTTING Al-Si CUTTINGS AC3A |
S. Zaima |
| 42 | Study on the Machinability of Aluminium Alloy (XXIV) CONSIDERATIONS OF THE CUT SURFACE OF A FACING ALUMINIUM ALLOY PLATE |
S. Zaima |