Metallurgical Asstracts on Light Metal and Alloys

vol.11

INDEX

No Title Author
1 Microstructure of That Part of Cold-rolled Aluminium Plate Unaffected by Welding Heat T. Enjyo
2 Electromigration of Grain Boundaries in Aluminium K. Hirano
3 Solid Solubility of Gold in Aluminium K. Hirano
4 Prolonged Ageing of an Al-0.22% Zr Alloy S. Hori
5 Effect of Precipitates on the Recovery and Recrystallization of Al-0.22% Zr Alloy S. Hori
6 Effects of Small Addition of Fe and Si on Ageing Process of Subperitectic Al-Zr Alloys S. Hori
7 Solidified Structures and Their Orientation of Aluminium Alloys by Centrifugal Casting R. Ichikawa
8 A General Treatment of the Distribution of Vacancies to Solute Atoms in a Ternary Solid Solution and Its  Application to Low Temperature Ageing of Al-Cu-Sn Alloys H. Kimura
9 Change in Coloring of Alumina Films Anodized with Pulse-shaped Current in Sulphuric Acid Solution T. Takahashi
10 Grindability and Ground-damaged Structure of Aluminium-Silicon Cast Alloys K. Kishi
11 Deformation and Fracture of Primary Silicon Crystal and Eutectic Phase in Hypereutectic Al-Si Alloy during Hot Machining K. Kishi
12 The Morphological Investigations of Machined Surface, Chip and Cutting Zone by Scanning Electron Microscope K. Kishi
13 Formation of Built-up Edges in Cutting Al-Si Alloys K. Kishi
14 Quantitative Analysis of Binary Al-Cu Alloys with Electron Probe Microanalyzer S. Maruno
15 New Structural Form of Sandwich Core K. Miura
16 Strength of Aluminium Plates with Indented V-notches M. Miyagawa
17 Study on the Improvement of Air Tightness in Aluminium Welds M. Mizuno
18 Reversion Characteristics in Al-4wt% Cu Alloy Y. Murakami
19 Analysis of Data on Zn Penetration along Random Grain Boundaries of Pure Aluminium S. Nishikawa
20 Plastic Deformation of [001] Oriented Aluminium Bicrystals
—Effect of Magnesium as Impulity—
F. Seki

Back to top

21 Dependence of Anodized Coating on the Crystallographic Orientation of Aluminium S. Ueda
22 Abnormal Layers in Anodic Oxide Coatings Formed on Aluminium by Prolonged Electrolysis S. Ueda
23 Effect of the Quality of Aluminium Alloys on the Formation of Abnormal Layers in Anodic Oxide Coatings S. Ueda
24 Characteristics and Structure of Double Anodic Oxide Coatings on Aluminium S. Ueda
25 Effect of Grain Size and Number of Primary Silicon Particles on the Machinability of Hypereutectic Al-Si Alloys H. Yamada
26 Effect of Modification with Sodium on the Age Hardening of Al-Si-Mg Cast Alloys H. Yamada
27 Anodizing of Al-High Si Alloys in Alkaline Media C. Yoshimura
28 Electron Microscopic Observation and Dyeing Affinity of Anodized Films Produced in Alkaline Media
STUDIES ON THE FINISHING OF ALUMINIUM IN ALKALINE MEDIA
C. Yoshimura
29 Study on the Built-up Edge in Drilling Aluminium Alloys (I)
RELATION BETWEEN THE PROFILE OF BUILT-UP EDGE AND THE CHIP FLOW ANGLE
A. Yuki
30 Study on the Built-up Edge in Drilling Aluminium Alloys (II)
SOME CONSIDERATION ON THE PROFILE OF BUILT-UP EDGE
A. Yuki
31 Study on the Mechanism of Drilling Aluminium Alloys (II)
OBSERVATION OF THE BUILT-UP EDGE IN DRILLING ALUMINIUM WROUGHT ALLOYS
S. Zaima
32 Study on the Mechanism of Drilling Aluminium Alloys (III)
SOME CONSIDERATIONS ON THE BUILT-UP EDGE IN DRILLING COMMERICAL ALUMINIUM-SILICON CAST ALLOYS
S. Zaima
33 Study on the Mechanism of Drilling Aluminium Alloys (IV)
INVESTIGATION OF THE BEHAVIOR OF BUILT-UP EDGES IN DRILLING AND IN ORTHOGONAL CUTTING OF ALUMINIUM WROUGHT ALLOYS
S. Zaima
34 Study on the Machinability of Aluminium Alloys (XXII)
EFFECTS OF MINOR CONSTITUENTS ON MACHINABILITY OF SILUMIN
S. Zaima
35 Study on Hot Machining of Some Hard-machining Aluminium Alloys (IV)
INVESTIGATIONS ON WARM MACHINING OF HIGH SILICON ALUMINIUM CAST ALLOYS
S. Zaima
36 Study on Hot Machining of Some Hard-machining Aluminium Alloys (V)
ON THE ORTHOGONAL HOT MACHINING OF HIGH SILICON ALUMINIUM CAST ALLOYS
S. Zaima

Back to top