INDEX
| No | Title | Author |
|---|---|---|
| 1 | On the Flow and Pressure Distribution during Rolling Wire Rods by the Three-Rolling System. | I. Gokyu |
| 2 | Fracture of Silicon Particles in Al-Si Alloys. | S. Hori |
| 3 | Effects of Cooling Rate and Degree of Supercooling on the Solidified Structures of Al-Mn, Al-Cr and Al-Zr Alloys in Rapid Solidification. | R. Ichikawa |
| 4 | Mechanical Properties of Rapidly Solidified Al-Zr -Cr and Al-Zr-Mn Ternary Alloys. | R. Ichikawa |
| 5 | Effect of Manganese on the Annealing Behaviour of Al-Mn Alloys. | S. Koda |
| 6 | Aluminum X-ray Emission Bands Applied to the Heat-induced Chemical and Structure Changes of Anodized Aluminum Films. | S. Maruno |
| 7 | Influence of Grain Size on the Portevin-LeChatelier Effect in Al-Mg Alloys. | S. Miura |
| 8 | The Influence of Grain-boundary Precipitate Particles on the Stress-Corrosion Cracking of Al-Zn-Mg Alloys. | Y. Murakami |
| 9 | Study on the Dynamic Thermal Stability of Al-0.25%Zr Alloy. | S. Nishikawa |
| 10 | Wear of Aluminium Alloys in the Combination of Three Different Materials. | K. Okabayashi |
| 11 | Radioactive Tracer Study of Inhibitive Action of Chromate Ions on Al Surface (I) | S. Tajima |
| 12 | On the Anomalous Behavior of Precipitates on a Scratched Surface of Al-4%Cu Alloy. | N. Takahashi |
| 13 | Morphology of Solid-Liquid Interface in Unidirectionally Solidified Aluminum and Aluminum-Zinc Alloys. | T. Takahashi |
| 14 | Morphology of Solid-Liquid Interface and Redistribution of Solute during Freezing of Aluminum Alloys. | T. Takahashi |
| 15 | Abrasion Tests of Anodic Oxide Flim on Aluminium by Taber Abraser. | S. Ueda |
| 16 | Effect of Si on the Recrystallization of Al-Mn Alloy. | H. Yamada |
| 17 | A Study on Internal Friction of Split-Aged Al-Mg-Si Alloys. | T. Yamane |
| 18 | The Temperature Dependence of Mechanical Properties of Al-Cu Alloy Single Crystals. | S. Yoshioka |
| 19 | Formation of Finished Surface in Drilling Aluminum and its Alloys. MACROSCOPIC OBSERVATION OF FINISHED SURFACES | A. Yuki |
| 20 | Effect of Environment on Formation of Finished Surface in Drilling Aluminium and its Alloys. | A. Yuki |
| 21 | Study on the Mechanism of Cutting Aluminium (XVII) OBSERVATIONS ON THE BUILT-UP EDGE IN ORTHOGONAL CUTTING OF SOME ALUMINIUM BINARY ALLOYS |
S. Zaima |
| 22 | Study on the Mechanism of Cutting Aluminium (XVIII) SOME CONSIDERATIONS ON THE CUTTING TEMPERATURE IN ORTHOGONAL CUTTING OF AN ALUMINIUM CAST ALLOY |
S. Zaima |
| 23 | Study on the Mechanism of Cutting Aluminium (XIX) SOME CONSIDERATIONS ON THE TOOL WEAR IN MACHINING HYPER-SILUMIN |
S. Zaima |
| 24 | Study on the Machinability of Aluminium Alloys (XV) MACHINABILITY OF NEW ALUMINIUM ALLOYS FOR PISTONS |
S. Zaima |
| 25 | Study on the Machinability of Aluminium Alloys (XVI) SOME CONSIDERATIONS ON THE EFFECTS OF TIN ON THE MACRINABIRITY OF ALUMINIUM-SILICON ALLOY CASTINGS |
S. Zaima |
| 26 | Study on the Machinability of Aluminium Alloys (XVII) CONTRIBUTION TO TOOL WEAR IN TURNING OF HYPERSILUMIN |
S. Zaima |
| 27 | Study on the Machinability of Aluminium Alloys (XVIII) STUDY ON THE MACHINABILITY OF ALUMINIUM-SILICON JIS COMMERCIAL CAST ALLOYS |
S. Zaima |
| 28 | Study on Hot Machining of Some Hard-Machining Aluminium Alloys (II) EFFECTS OF CUTTING TEMPERATUREON MACHINING ACCURACY IN TURNING OF ALUMINIUM ALLOYS |
S. Zaima |